To have a maximum safety the helmet must fit tightly and be correctly and securely fastened, in order not to be able to be taken off neither by pulling it nor by rotating it around the head.
If it is too big, it may slide down over the eyes or turn in a lateral direction due to movement during riding, blocking the right visibility.

SHELL in TRICARBOCO material, mix of Kevlar, carbon and fiber, joint through resine, hand made, using new technologies with vinilester resin.

The INTERNAL POLYSTYRENE produced in 3 sizes to get the best fitting. This characteristic allows a gradual and progressive absorption of the energy produced by the impact.
Even if the bigger part of the energy created by the impact is absorbed by the external shell, thanks to its deformation, the role of polystyrene is determinant for the absorption of the residual energy.
A diversified density of the polystyrene, permit us to optimize the mechanical performance of the shell/polystyrene.

The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw.
After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head.
If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet.
Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs.
To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings».
Use the release tab only to remove the helmet! Never release this tab while riding.

The internal polystyrene has been studied to work together wityh the air ventilations, put on the shell. The channels allow the perfect inside air flow and at the same time a quick outside air flow from back ventilation.

ALPHA is homologated as per the following rules:

ECE 22-05	Europe
DOT	America and Canada
INMETRO NBR 7471	Brasil

You have to refer always to the homologation of the country in which the helmet is sold.

The CHEEK PADS and the INTERNAL COMFORT shell can be removed, washed and replaced.

They are made of a precious fabric with specific fibers, that offer:

• It moves away the body sweat;
• Keeps rider fresh, dry and completely comfortable;
• Lightweight, soft and breathable fabric;
• Performance controlled and certified by ADVANSA.

The cheek pads are easily removable also in case of accident through a red strap which removes the cheek pad even if the helmet is worn by the rider.

	SIZES	CM	INCH
	XS	53/54	6 1/2” - 6 5/8”
	S	55/56	6 3/4” – 6 7/8”
	M	57/58	7” – 7 1/8”
	L	59/60	7 1/4” – 7 3/8”
	XL	61/62	7 1/2” – 7 5/8”
	XXL	63/64	7 3/4” – 7 7/8”

SPARE PARTS DESCRIPTION		CODE
Inner Covered Chin Guard		KAAL0M00
Top Air Vent	White	KAALTV01
	Black	KAALTV02
Chin Guard Air Vent	White	KAALVM01
	Black	KAALVM02
Screw Kit		KAALVF00
Inner Comfort Liner removable and washble	Size XS	KAAL0I01
	Size S	KAAL0I02
	Size M	KAAL0I03
	Size L	KAAL0I04
	Size XL	KAAL0I05
	Size XXL	KAAL0I06
Cheek Pads	Size XS	KAAL0L01
	Size S	KAAL0L02
	Size M	KAAL0L03
	Size L	KAAL0L04
	Size XL	KAAL0L05
	Size XXL	KAAL0L06

KSAL00W3 - Plain White		KSAL0001 - Bike Orange
KSAL0002 - Bike Grey		KSAL0003 - Bike Blue
KSAL0004 - Bike Red		KSAL0005 - Bike Yellow
KSAL0006 - Bike Green		KSAL0007 - Warrior
KSAL0008 - Pixel